Holybro KAKUTE H7 v1.3 STACK

Holybro KAKUTE H7 v1.3 STACK

• The Holybro Kakute H7 v1 Flight Controller is full of features including integrated Bluetooth, dual plug-and-play 4in1 ESC ports, HD camera plug, barometer, OSD, 6x UARTs, full Blackbox MicroSD card slot, 5V and 9V BEC, easy soldering layout and much more.
• The Kakute H7 builds upon the best features of its F7 predecessor and further improves on hardware components and layout. With the additional integrated Bluetooth chip onboard, you can perform Betaflight configuration and tuning wirelessly on your phone with the SpeedyBee Android & IOS App. The Kakute H7 is DJI HD ready. It has an easy plug-and-play port with an on-board 9V regulator designed to power your HD video transmitter like DJI/Caddx FPV Air Unit & Caddx Vista while supporting analog system.
• It has 6x dedicated UART ports with built-in inversion for peripherals (UART2 is used for Bluetooth telemetry), along with a full MicroSD Card slot for virtually unlimited Blackbox data logging. Dual plug-and-play 4in1 ESC connectors, allowing easy plug-and-play support for x8 Octocopter configuration and keeping it simple and clean. The integrated BetaFlight OSD makes it easy to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. It is also ready for autonomous flight with the on-board barometer. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers.

Follow us World Drone Market on our YouTube to view more about the Holybro KAKUTE H7 v1.3 STACK.

Kakute H7 V1.3 Specification :

• MCU – STM32H743 32-bit processor running at 480 MHz
• Professional underfill epoxy for mechanical reinforcement
• IMU – MPU6000
• Barometer – BMP280
• OSD – AT7456E
• Onboard Bluetooth chip – ESP32-C3
• SpeedyBee IOS & Android App Compatible
• Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm) in Betaflight
• 6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
• 9x PWM Outputs (8 Motor Output, 1 LED)
• 2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible)
• 1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit)
• Battery input voltage: 2S – 8S
• BEC 5V 2A Cont.
• BEC 9V 3A Cont
• USB Type-C
• Mounting – 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
• Dimension – 35x35mm
• Weight – 8g

Firmware Targets

• BetaFlight: KakuteH7 (v4.2.11 and above)
• INAV: KakuteH7 (4.0.0 & above) SD card support added in 4.1.0.
• ArduPilot: KakuteH7 (4.2.0 & above)

Package Includes:

• 1x Kakute H7 V1.3 Flight Controller
• 4x M3 Silicon Grommets
• 2x JST-SH1.0_8pin 150mm Cable (For ESCs)
• 2x JST-SH1.0_6pin 80mm & 150mm Cable (For DJI Air Unit)
• 1x JST-SH1.0_6pin Colored Silicon 150mm Cable (For Caddx HD System and other VTX)

Tekko32 F4 4in1 60A ESC

The Tekko32 F4 4in1 60A ESC is a high-performance electronic speed controller. This compact 4-in-1 ESC is designed with a 30×30 mounting pattern and supports 3-6S LiPo batteries. It has all new High-quality MOSFETs with low internal resistance and low heat generation, ensuring efficient power delivery and a smooth flight experience while allowing the ESC to boast a continuous current of 60A. It has a separate drive and control circuit to broaden the current capability of the drive circuit while reducing electrical interference in the control circuit. With its cutting-edge BLHeli_32 firmware and 96K PWM frequency, enjoy lightning-fast response times and exceptional motor control.

Features:

• All new High-quality MOSFETs with low internal resistance and low heat generation
• Fast F4 MCU @150MHz (compared to F3 @108MHz & F0 @48MHz)
• A separate drive and control circuit, reducing the electrical interference
• Continuous Current Rating of 60 Amps

Specification:

• Continuous Current: 60A x4
• Burst Current: 70A x4
• Battery Supports: 4-6S
• PWM Frequency: 16k to 96k
• Supports DShot 150/300/600/1200/2400
• Supports MultiShot/OneShot/Proshot/PWM etc.
• ESC telemetry Supported
• Onboard analog current sensor
• BLHeli_32 firmware
• 1000uf 35v capacitor included (highly recommended for 6s setup)
• Amperage meter scale ratio: 120
• Dimensions: 48x37x6mm / Weight: 15.7g
• Mounting holes: M4 30.5×30.5mm (M3 grommets included)