Table of Contents
Skydroid H12 Pro User Manual
Overview
Product Features
- The H12 Pro series uses newest Qualcomm Snapdragon 625 processor, equipped with an Android embedded system and advanced SDR technology and super protocol stack, making the image clearer, lower the latency, longer distance, stronger anti-infection, whether it is drones, robots, industrial control equipment, etc. can be applied.
- We provide development kits, SDKs and technical support for digital cameras, serial transparent transmission, sbus and other rich interfaces. Equipped with Type-C 3.0 high speed interface, expanded TF card slot, etc.
- The 1920 * 1080 resolution high brightness display screen, with a large proportion of screens, can still clearly view the real-time display information in a sunny environment.
- The 2T2R dual antenna signals complement each other, with ultra-high sensitivity, ultra long distance, and advanced frequency hopping algorithms, greatly enhancing weak signal communication capabilities.
- Skydroid Fly App has undergone a lot of optimization based on QGC, a better interactive interface, a larger controllable map field of viewing, the aircraft implements intelligent waypoint planning, automatic execution, automatic follow-up, and one-click home, highly provides working effectiveness in professional fields.
Main applications
It is used to remotely operate helicopters, fixed wings, multi-rotors, vehicles, ships, etc. for video/image transmission (camera optional), data transmission, telemetry, and control.
Specification
| Remote Controller Specification | |||
| Model No. | H12PRO | Channels | 12 |
| Working voltage | 4.2V | RF Power | 17.5dBm |
| Frequency | 2.400-2.483GHz | Frequency hopping | OFDM |
| Update way | APP Update online | Weight | 660g |
| Size | 190*152*94mm | Battery | 10000mA/H |
| Endurance | 6-20Hrs | Charging port | TYPE-C |
| Modulation mode | CCK,DQPSK,DBPSK | Transmission rate | 6.5-144Mbps |
| Transmission power | 2.4G: 16.0±1.5dBm&<-15dB@11b 11Mbps;14.0±1.5dBm&<-25dB@11g 54Mbps13.0±1.5dBm&<-28dB@11n-HT20-2.4G-MCS7;13.0±1.5dB- m&<-28dB@11n-HT40-2.4G-MCS7 | ||
| Receiver sensitivity | 2.4G:1Mbps:-94dBm@PER<8%;11Mbps:-85dBm@PER<8% 54Mbps:-70dBm@PER<10%;HT40-MCS7-2.4G:65dBm@PER<10% | ||
| Working Range | Open & no interference from ground to air:6~10KM Open & no interference ground: 1.2~1.5KM Indoor 3~4 walls: 30M | ||
Receiver Specification | |||
Model No. | R12PRO | Channels | 12 |
Working Voltage | 4.5-5.5V | Working current | 300mA~800mA@5V |
Size | 51*41*13mm | Weight | 14g |
The composition of the model and its significance
H12 Pro controller body
Number | Annotation | Number | Annotation |
1 | 2.4G 4dB antenna |
11 | Right joystick X2、Y2 |
2 | Toggle 3 positions switcher/ working modes |
12 | Button D (No function currently available) |
3 | Thumbwheel switch G (No function currently available) |
13 | humbwheel switch H (No function currently available) |
4 | Button C (No function currently available) |
14 | Toggle 3 positions switcher (No function currently available) |
5 | Left joystick X1、Y1 |
15 | Dust plug |
6 | Display |
16 | SIM card slot |
7 | MIC |
17 | Charging port |
8 | Button A (No function currently available) |
18 | 4 pin ip port |
9 | Power switcher |
19 | No function currently available |
10 | Button B (No function currently available) |
|
Remarks: ⑥Touch screen, you can click the screen to operate. Please pay attention to waterproof the screen when using it (such as avoiding rain water falling on the screen in rainy days), so as to avoid damage to the screen caused by water ingress.
Receiver
Name | Annotation | Name | 注解 |
| 2.4 ANT | Antenna | |
LED | Binding indicator light | ETH0_TX+ |
IP port 0 |
GND | Ground | ETH0_TX- |
|
KEY | Binding key | ETH0_RX+ |
|
PWM0/CH9 | PWM0 | ETH0_RX- |
|
PWM1/CH10 | PWM1 | GND |
Telemetry |
GND | Ground | 5V_IN |
|
ETH1_TX+ |
IP port 1 | UART_RX |
|
ETH1_TX- |
| UART_TX |
|
ETH1_RX+ |
| GND |
Sbus |
ETH1_RX- |
| SBUS |
|
| 2.4G ANT | Antenna | |
Attention:Dual PWM function is under debugging, firmware support can be upgraded through OTA in the near future.
H12Pro remote control cannot be used while charging.
Remote control antenna angle
Adjust the angle of the remote control antenna to face the flight direction of the drone.
Antennas shall not form shielding or crossing with each other.
Environment conditions
Pay attention
Working temperature
Relative humidity：Not exceed 85%。
Atmospheric pressure:86kPa~106kPao
Working environment should not contain explosive material or any corrosive or harmful gas may cause interference in the operation of the product.
Always work under shelter to prevent rain, snow, wind, sand and dust contamination.
Working conditions
Power supply and attentions
H12Pro series uses a built in Li-ion battery. Charging port is compatible with 9V -2A Type-C chargers (such as cell phone, digital cameras’ USB charger).
In case of smoke, heat or unusual smell during charging, please stop charging immediately and return to our company for servicing as soon as possible.
Do not leave the product unattended while charging. Do not leave the product in a place where children can reach. Do not charge when room temperature over 60 ℃
Safety
Warning
Beginners should pay attention for the followings! Please read it carefully!
DO NOT fly under the influence of substances, or when tired!
DO NOT fly in strong wind and or rainy conditions!
DO NOT fly close to electric emission towers, communication stations and crowded area!
DO NOT fly nearby airports and other prohibited areas!
DO NOT fly around people or animals, or in any location where possible to damage property
Check equipment before every flight and check whether the transceiver system and the drones are normal or not
Please use certified chargers to charge the batteries.
DO NOT put unnecessary force on antennas since its weakness.
Operation
Preparation and pre-checking before use
Pay attention
- Check battery level.
- Check position of the antenna to get the best performance
- Make sure the firmware is the latest version
- DO NOT operate under the influence of alcohol or drugs
Operation
Language setting
Enter setting, and then enter system, choose your language
Status bar
- Bluetooth
- Signal
- SIM card status (without sim card in the picture)
- Power lever (charging in the picture)
- Time
- Back ground management
- Home
- Return to last step
H12 Pro Assistant
- Mode change
- Rudder value
- Binding the remote control with other receivers (the binding method is introduced in below)
- Video/image transmission checking
- In the advanced parameters setting, you can adjust the channel, upgrade the joystick firmware, and modify the receiver’s serial port baud rate (password is：999)
Binding operation
- Power on the receiver and the red light remains on. After around 10 seconds, the blue light flashes slowly.
- After the blue light flashes slowly, wait for another 20 seconds, short circuit GND and KEY until the blue light flashes quickly and then release.
- Open the H12 Pro assistant on the remote control, click on“ binding”, start it and wait for the display showing you“ Binding successful”.
- The receiver indicator light will flash continuously for two minutes before turning blue and remaining on.
Attention：H12Pro remote control cannot be used while charging
Image connection settings
H12Pro Assistant – Video View – Click the Settings button below – Video Stream Address – Customize, enter the camera address.
The network segment of the network camera needs to be set in advance into 144 network segment (192.168.144.XXX), and then connect the camera to the receiver ip port 0 or ip port 1.
Settings: This setting displays image transmission through the ip port on the receiver, displaying C10 three-axis gimbal (when C10 is connected) rtsp://192.168.144.108:554/stream=0
To install a third-party ip camera, you need to ask the camera manufacturer for an RTSP address.
H12 Pro image and data transmission in ground stations APP
Open the Skydroid ground station, click on the pop-up sidebar in the upper left corner, and click on“ Switch Connection”.
Select the APM/PX4/H112Pro combination and click to enter.
Common Settings →Other Settings →User Interface →Video Window →C10
Note: If it is a 3rd party’s IP camera, select“ Custom” and enter the corresponding video stream address is OK.
H12 Pro image and data transmission in ground stations APP
Telemetry sharing
The remote control is connected to the computer network port through an Ethernet cable
Open computer settings ->click on adapter ->select Ethernet ->select IPV4 protocol ->select
custom IP address ->enter as shown in the diagram ->click confirm (see picture below)
Open the QGC in computer and select Application Settings
Select communication connection and add connection ways
Custom name, select UDP, port number is 14550
Select the established connection way and click on Connect
Video transmission sharing
After connecting the remote control to the computer as described above, download the software“ VLC” to display the image.
Open the computer“ VLC” software and select Network Streaming in the media
In the input field of the network URL, enter rtsp://192.168.144.108:554/stream=0, and then click to play
Leave a comment
You must be logged in to post a comment.