Table of Contents
Skydroid-H30 R30 User manual
Overview
Product Features
(1)The H30 uses the newest Qualcomm Snapdragon 660 8-core processor, equipped with an Android 9 (64bit) embedded system and advanced SDR technology, also with a super protocol stack to make the image clearer, lower latency, longer distance transmission, and stronger anti-interference. Wildly applied for drones, Robots, industrial controlled equipment, etc.
(2)Supports rich interfaces such as HDMI, RJ45, sensor interface, dual serial ports passthrough transmission, SBUS, aerial photography, FPV security, fire protection, power, mapping robot, border control, etc.
(3)Equipped with IP65 waterproof, dust-free structural design, ensuring not only good using feel but also durability.H30 uses 10.1-inch FHD high-brightness IPS LCD screen display, which can be viewed clearly under the sun. The resolution is 1920*1200. Supports 1080P high-definition digital image transmission. The dual-3 frequencies antenna signals complement each other, with super-strong signals and ultra-long transmitting distances, combined with algorithm control and out-of-step frequency hopping algorithms, greatly increasing the ability to communicate with weak signals. So you don’t need to worry about the flight distance during flight operations, just explore a wider scenery. Built-in dual speakers, triple frequencies as 800M, 1.4G, 2.4G, WiFi 2.4 & 5G.
(4)Integrated with high energy density lithium ion battery, can work for 5 hours after full charging. The consistent survival thinking in the wilderness allows you to have no concerns about the reliability of our equipment.
(5)H30 supports rich interfaces such as HDMI, SIM card, USB, Type-C, RJ45, PPM and dual serial port passthrough transmission, dual net ports and SBUS for the R30. And supports many brands cameras, pan-tilts, pods and other video equipment. Provide development kit, SDK and technical support, support video suspension, support ground station of mainstream flight control, support QGC and wireless RTSP video stream sharing.
(6)The use of weather silica gel, frosted rubber, stainless steel, and ABS makes the extreme operating feel, and also meets the harsh conditions of outdoor use of drones..H30 is dust-free in the fuselage, control switches, and various peripheral interfaces. Protective measures such as splashing can ensure stable and smooth operation of the equipment in harsh environments.
(7)Rich ground-end interface, RJ45 network interface, long-distance connection to the internal network, Type-C Android high speed USB interface, OTG interface can be connected to U disk and network card, etc., expanded TF card slot.
(8)An independent 2-dimensional gimbal joystick makes the gimbal flying with great facility, like a duck to water.
Main purpose and scope of application
It is used to remotely operate helicopters, fixed wings, multi-rotors, vehicles, ships, etc. for video image transmission (optional camera), data transmission, and control drone flight.
Specifications
Remote Controller Specification | |||
Model No. | H30 | Channels | 16 |
Working voltage | 4.2v(Battery built-in) | RF Power | 23dBm@CE/FCC |
Frequency | 800M/1.4G/2.4G | Dynamic FM | supports frequency hopping across frequency bands |
Size | 346(L)*196.5(W)* 89.4(H)mm | Weight | 1.5kg |
Endurance | 5 hours | Battery | 20000mA/H |
Update way | APP Update online | Charging port | TYPE-C |
Run memory | 4G | Store memory | 64G |
Applications | Helicopter, fixed wing, multi-rotor, unmanned vehicle, unmanned boat, etc. |
Receiver Specification | |||
Model No. | R30 | Channels | 16 |
Working Voltage | 7.2V~72V | RF Power | 23dBm@CE/FCC |
Size | 76.4(L)*59(W)* 15(H)mm | Weight | 65g |
The composition of the model and its significance
Number | Annotation | Number | Annotation |
1 | 800M/1.4G/2.4G Three working frequencies antenna | 9 | MIC |
2 | Knob switch AUX1 | 10 | Key button H |
3 | Three levers switcher SW1 | 11 | R2 button |
4 | Left joystick X1、Y1 | 12 | R1 button |
5 | Small left joystick X3 、Y3 | 13 | Small right joystick X4 、Y4 |
6 | L1 button | 14 | Right joystick X2、Y2 |
7 | L2 button | 15 | Three levers switcher SW2 |
8 | Power button | 16 | Knob switch AUX2 |
Number | Annotation | Number | Annotation |
17 | HDMI | 21 | RJ45 |
18 | SIM card slot | 22 | TF card slot |
19 | USB | 23 | PPM |
20 | TYPE-C | 24 | Wrapping connector |
Number | Annotation | Number | Annotation |
1 | Serial port 0 | 7 | Binding key |
2 | Serial port 1 | 8 | Network port 0 |
3 | Reserved port (unavailable) | 9 | Network port 1 |
4 | Power supply 7.2~72v input and SBUS | 10 | External binding key |
5 | Type-c | 11 | MMCX |
6 | Binding status indicator |
Port Definition Diagram
Environment conditions
Pay attention
Working temperature:-10°C~+55°C。
Storage temperature:-25°C~+70°C。
Relative humidity:Not exceed 85%。
Atmospheric pressure:86kPa~106kPao
Working environment should not contain explosive material or any corrosive or harmful gas may cause interference in the operation of the product.
Always work under shelter to prevent rain, snow, wind, sand and dust contamination.
Working conditions
Power supply and attentions
H30 series uses a built in Li-ion battery. Charging port is compatible with common Type-C (such as cell phone, digital cameras’ USB charger).
In case of smoke, heat or unusual smell during charging, please stop charging immediately and return to our company for servicing as soon as possible.
Do not leave the product unattended while charging. Do not leave the product in a place where children can reach. Do not charge when room temperature over 60 ℃.
Safety
Warning
Beginners should pay attention for the followings! Please read it carefully!
DO NOT fly under the influence of substances, or when tired!
DO NOT fly in strong wind and or rainy conditions!
DO NOT fly close to electric emission towers, communication stations and crowded area!
DO NOT fly nearby airports and other prohibited areas!
DO NOT fly around people or animals, or in any location where possible to damage property.
Check equipment before every flight and check whether the transceiver system and the aircraft are normal or not.
Please use certified chargers to charge the batteries.
DO NOT put unnecessary force on antennas, joystick and screen since their weakness.
Operation
Preparation and pre-checking before use
Pay attention
① Check battery level.
② Check position of the antenna to get the best performance.
③ DO NOT operate under the influence of alcohol or drugs.
Operation
Language setting
① Enter system setting, choose your language and input method
② Once entering language and input method choosing, you can add/cancel/choose the language you want
① WIFI connection
② SIM card signal
③ Power display
④ Return
⑤ Home
⑥ Background task management
H30 Assistant
① Mode setting: Switch the operating mode of the remote control’s joystick (mode type: Mode 1, Mode 2. Default Mode 2), 1. Read 2. Set 3. Save.
② Video viewing: You can view RTSP videos (detailed on the next page)
③ Check whether the values of each channel of the remote controller are normal or not
④ Wireless parameter configuration. Binding the remote control with other receivers (the binding method is described below: image connection and settings)
⑤ Signal viewing (viewing signals)
⑥ In the advanced setting, the receiver’s serial port baud rate, remote control parameter adjustment, device upgrade, SN, coaching mode (under development), and wireless module upgrade can be adjusted and modified (password: 999, for professional debugging only)
Note:that the complete set of remote controller and receiver is already binding before leaving the factory. You only need to power on and wait for 20 seconds for automatic binding.
① Power on the receiver, the power light – red light is always on. After waiting for 20 seconds, press and hold the receiver SET binding key – the blue light flashes and then release it; Replacement controller or receiver requires a new frequency binding.
② Enter the H30 Assistant APP and click binding. Binding status: on binding… After successful binding, the status will show “Connected” and “Binding succeeded” (the receiver’s green light is always on).
Video/Image Connection and Settings
The network segment of the network portal camera needs to be set to 144 network segments (192.168.144.XXX) in advance. The camera connects to the receiver network port 0 or network port
1. For pin definitions, see “I. Overview ->5. Port Definition Diagram” in this article.
Settings: This setting displays the transmission of images through the air unit network port, and displays the C10 three-axis gimbal camera (when C10 is connected)
rtsp://192.168.144.108554/stream=0. If want to install a third-party gimbal camera, you need to ask the camera manufacturer for the rtsp address.
How to display telemetry and image transmission on H30’s ground station
FC’s data cable connects to the serial port 0, take Skydroid tower shows telemetry as an example (H30 Assistant should be quit)
Skydroid tower:
Serial port 0: Server IP: 192.168.144.101 Server port: 14550 Click to connect directly.
Serial port 1: Server IP: 192.168.144.101 Server port: 14551 Click to connect directly.
C10 three-axis gimbal connects to network port 0 or network port 1, take Skydroid tower showing video/picture transmission as an example.
More →Common Settings →Other Settings →User Interface →Video Window →C10 (Display C10 camera) →Customization (Input RTSP Address to Display Other Cameras) →C10 (Display C10 camera)
→Customization (Input RTSP Address to Display Other Cameras)
Take QGC in H30 to show video transmission as an example (H30 Assistant should be quit) 12
Click the Q icon in QGC to enter the settings.
① Click on General
② Change the Source to RTSP Video Stresm
③ Fill in the RTSP URL with the RTSP address of the network camera and the image of the C10 three-axis gimbal (which needs to be connected to C10) RTSP address
rtsp://192.168.144.108554/stream=0
Take QGC in H30 to show telemetry as an example
① Clack on Comm Links
② Clack ADD to change the Type to TCP and name it as name.
③ Serval port 0: Server Address changed to 192.168.144.101 Port listening port changed to 14550
Serial port 1: Server Address changed to 192.168.144.101 Port Listening port changed to 14551
④ Clack OK to save
How to connect the internet
The remote control can be connected to the Internet in three ways:
(1) connected to 5G Wi-Fi network
(2)connected to the RJ45 port of the remote control
(3)inset a SIM card
How to share internet, video/image transmission and data/telemetry transmission
Sharing telemetry
(1)The remote controller is connected to the computer network port through a network cable.
Note: The remote control ground station should be disconnected!
(2)Open “setting” in the PC, click on the “adapter”, select Ethernet, select the IPV4 protocol, select a custom IP address, enter according to the method in the figure, and click “OK”.
(3)Open the Mission Planner in computer and select TCP as the connection way.
(4)After clicking on the connection, enter IP: 192.168.144.101, and then click OK.
(5)Select 14550 as the port number on serial port 0, and click OK to connect (see the figure
below).
(6)Select 14551 as the port number on serial port 1 and click OK.
Sharing video/image transmission
Connect the network cable as described above, share telemetry →set a fixed Ethernet IP address.
Download VLC EXE. To show video/image
① Open VLC and choose network streaming
② Enter “rtsp://192.168.144.108554/stream=0” to URL and click “play”
Follow us World Drone Market on our YouTube to view more about the Skydroid H30.
Leave a comment
You must be logged in to post a comment.