Search

For bulk order, please contact sales@worldronemarket.com and we will provide the best service and price for you. Thank you!

T-Motor FLAME 200A 14S ESC 6-14S

Product codeTM103
Availability In stock (can be backordered)

$499.00

Buy it now

T-Motor FLAME 200A 14S Multi-Rotor Uav Drone ESC 6-14S battary

Model Continuous Current Peak Current(10s) BEC LiPo Programable item(s) Weight(g) Size /L*W*Hltem(mm)
FLAME 60A 12S 60A 80A NO 6-12S NO 73.5 66.5*38.5*17.7
FLAME 70A 6S 70A 80A NO 4-6S NO 55 56.6*36.4*16.1
FLAME 80A 12S V2.0 80A 120A NO 6-12S NO 109 84*35.5*19.5
FLAME 100A 6S 100A 120A NO 4-8S NO 78.5 72.2*30.6*17.3
FLAME 100A 14S 100A 120A NO 6-14S NO 139 86.1*54.1*24
FLAME 180A 12S V2.0 180A 200A NO 6-12S NO 279 112.2*50.5*35.5
FLAME 200A 14S 200A 240A NO 6-14S NO 558 106*50*48.5
To avoid irreparable damage to ESCs, please keep strict compliance with the input voltage range !
THROTTLE CALIBRATION

Calibrate the throttle range whenever you install a new FLAME ESC or a new RC radio. For safety, remove all propellers before you start throttle calibration!

Throttle Range Calibration

First, power on your transmitter and push the throttle stick to its maximum position. Next, connect the battery to your receiver. Confirm your transmitter and receiver bind properly, then power on the ESC. After the motor makes two short beeps (beep-beep), pull the throttle stick all the way down within 3 seconds. The motor will sound one long beep to confirm. You have now finished throttle calibration.

If you fail to pull the throttle stick to the bottom, the motor will keep making short beeps. When this happens, run the calibration process again.

ESC Programming (For FLAME 80A 12S V2.0 only)

First, turn on the transmitter and push the throttle stick to full throttle. Then connect the battery to the receiver. Double-check your transmitter and receiver bind successfully, and power on the ESC. The motor will cycle through a sequence of different beep tones.

  • Beep-beep — Throttle Calibration
  • Beep-beep-beep — Intermediate Timing
  • Beep-beep-beep-beep — High Timing Once you hear the tone for your target setting, wait 3 seconds, then pull the throttle stick down. This action saves your selected programming option. You complete programming after this step.
NORMAL STARTUP PROCESS

Power on the transmitter and keep the throttle stick at the lowest position. After you plug in the battery, the motor sends one long beep after 1 second. This tone tells you the ESC and multirotor are ready for flight.

PROTECTIONS

Engineers design this ESC specifically for multirotor platforms. Start-up Protection: If the ESC cannot spin up the motor normally within 2 seconds while throttle rises, it stops the motor. To recover, pull your transmitter throttle stick back to the bottom and re-arm. Common triggers include loose or broken wiring between ESC and motor, or blocked propellers.

Throttle Signal Loss Protection: If the ESC loses throttle signal for more than 0.25 seconds, it immediately cuts power output. This prevents dangerous sustained high-speed prop rotation. The ESC restores normal power once it receives valid signals again.

Motor Lock-up Protection: When the ESC detects a locked motor, it attempts three restarts. If restart attempts fail, the ESC cuts output and stops retrying. To reset the ESC, pull the throttle stick to minimum and re-arm.

Over-load Protection: The ESC cuts power instantly when peak current nears 340A (short-circuit current). Power cycle the ESC to restore normal operation.

TROUBLE SHOOTING
Trouble Warning Tone Possible Cause Solution
The ESC was unable to start the motor “Beep beep beep…”(the motor beeped rapidly) The throttle stick was not on the bottom position or the throttle range was too narrow Move the throttle stick to the bottom position or recalibrate the throttle range
The ESC was unable to start the motor “Beep、beep、beep…”(time interval is 1 second) No output signal emitted from the throttle channel on the receiver Check if the transmitter and receiver are well bound Check if the throttle wire has been properly plugged into the channel into the receiver
The ESC was unable to start the motor “Beep beep beep beep…(these tones are plaed circularly) The voltage was below 18.6V Change another battery with normal voltage(18.6-55V)
The ESC was unable to start the motor “beep beep beep、beepbeep beep…”(these tones are played circularly) The voltage was above 55V Change another battery with normal voltage(18.6-55V)
If you encounter any problems using FLAME ESC, please feel free to contact our distributors or T-MOTOR directly.

Follow us World Drone Market on our YouTube to view more about the T-Motor FLAME 200A 14S Multi-Rotor Uav Drone ESC 6-14S battary.

FLAME 200A 14S Multi Rotor Uav Drone ESC 6 14S battary 1 - T-Motor FLAME 200A 14S ESC 6-14S FLAME 200A 14S Multi Rotor Uav Drone ESC 6 14S battary 5 - T-Motor FLAME 200A 14S ESC 6-14S FLAME 200A 14S Multi Rotor Uav Drone ESC 6 14S battary 3 - T-Motor FLAME 200A 14S ESC 6-14S FLAME 200A 14S Multi Rotor Uav Drone ESC 6 14S battary 4 - T-Motor FLAME 200A 14S ESC 6-14S FLAME 200A 14S Multi Rotor Uav Drone ESC 6 14S battary 2 - T-Motor FLAME 200A 14S ESC 6-14S

Weight 1 kg

Customers reviews

There are no reviews yet.

Be the first to review “T-Motor FLAME 200A 14S ESC 6-14S”
Back to Top
Product has been added to your cart