Search

For bulk order, please contact sales@worldronemarket.com and we will provide the best service and price for you. Thank you!

T-Motor FLAME 100A 14S ESC 6-14S

Product codeTM100
Availability In stock

Price range: $89.99 through $129.99

Buy it now

T-Motor FLAME 100A 14S Multi-Rotor UAV Drone ESC 6-14S

P55 Industrial

T-Motor FLAME 100A 14S Multi-Rotor UAV Drone ESC 6-14S FLAME 100HV 500HZ 6-14S LIPO U12 PERFECTLY COMPATIBILITY

Model Continuous Current Peak Current(10s) BEC LiPo Programable item(s) Weight(g) Size /L*W*Hltem(mm)
FLAME 60A 12S 60A 80A NO 6-12S NO 73.5 66.5*38.5*17.7
FLAME 70A 6S 70A 80A NO 4-6S NO 55 56.6*36.4*16.1
FLAME 80A 12S V2.0 80A 120A NO 6-12S NO 109 84*35.5*19.5
FLAME 100A 6S 100A 120A NO 4-8S NO 78.5 72.2*30.6*17.3
FLAME 100A 14S 100A 120A NO 6-14S NO 139 86.1*54.1*24
FLAME 180A 12S V2.0 180A 200A NO 6-12S NO 279 112.2*50.5*35.5
FLAME 200A 14S 200A 240A NO 6-14S NO 558 106*50*48.5
To avoid irreparable damage to ESCs, please keep strict compliance with the input voltage range !
THROTTLE CALIBRATION

Calibrate the throttle range whenever you install a new FLAME ESC or a new RC radio.
For safety, remove all propellers before you start this throttle calibration procedure!

Throttle Range Calibration

First, power on your transmitter and push the throttle stick all the way to maximum.
Next, connect your receiver to the battery. Confirm a stable bind between transmitter and receiver, then power on the ESC.
When the motor emits two short “beep-beep” alerts, pull the throttle stick to minimum within 3 seconds. You will then hear one long “beep”.
This long beep signals that throttle calibration has completed successfully.

*If the throttle stick is not pushed to the bottom position, the motor will emit short beeps. In that case, you need to recalibrate!

ESC Programming (For FLAME 80A 12S V2.0 only)

Turn on the transmitter and push the throttle stick all the way to the top. Next, connect the receiver to the battery. Confirm that the transmitter and receiver bind properly, then power on the ESC. After the ESC boots, the motor will cycle through a sequence of different beep tones.

  • Two beeps: Throttle Calibration
  • Three beeps: Intermediate Timing
  • Four beeps: High Timing Once you hear your target beep sequence, wait 3 seconds and then pull the throttle stick down to the bottom position. This action saves your selected programming option. Finally, you finish the programming process.
NORMAL STARTUP PROCESS

Turn on the transmitter and push the throttle stick to the bottom position.

The motor will emit a long “beep—-” 1 second after you connect the system to the battery, which indicates the ESC and multi-rotor are ready.

PROTECTIONS
This ESC is specially designed for multi-rotors.
  1. Start-up Protection: If the ESC fails to spin up the motor within 2 seconds after you raise the throttle, it stops the motor. In such cases, pull the transmitter throttle stick all the way down and restart the motor. Common triggers include loose or disconnected wires between the ESC and motor, or blocked propellers.
  2. Throttle Signal Loss Protection: Once the ESC loses throttle signals for more than 0.25 seconds, it immediately cuts power output. This action prevents severe hazards from propellers or rotor blades running at sustained high speed. The ESC restores matched output once it receives valid signals again.
  3. Motor Lock-up Protection: When the ESC detects a locked motor, it attempts three restarts. If all attempts fail, the ESC cuts output and stops further retries. To reset the ESC and restore power, move the throttle stick to the lowest position and reinitiate startup.
  4. Over-load Protection: The ESC instantly cuts output whenever peak current nears 340A (short-circuit current). Power cycle the ESC to return it to normal operation.
TROUBLE SHOOTING
Trouble Warning Tone Possible Cause Solution
The ESC was unable to start the motor “Beep beep beep…”(the motor beeped rapidly) The throttle stick was not on the bottom position or the throttle range was too narrow Move the throttle stick to the bottom position or recalibrate the throttle range
The ESC was unable to start the motor “Beep、beep、beep…”(time interval is 1 second) No output signal emitted from the throttle channel on the receiver Check if the transmitter and receiver are well bound Check if the throttle wire has been properly plugged into the channel into the receiver
The ESC was unable to start the motor “Beep beep beep beep…(these tones are plaed circularly) The voltage was below 18.6V Change another battery with normal voltage(18.6-55V)
The ESC was unable to start the motor “beep beep beep、beepbeep beep…”(these tones are played circularly) The voltage was above 55V Change another battery with normal voltage(18.6-55V)
If you encounter any problems using FLAME ESC, please feel free to contact our distributors or T-MOTOR directly.

Follow us World Drone Market on our YouTube to view more about the T-Motor FLAME 100A 14S Multi-Rotor UAV Drone ESC 6-14S.

FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 1 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 2 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 5 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 6 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 7 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 4 - T-Motor FLAME 100A 14S ESC 6-14S FLAME 100A 14S Multi Rotor Uav Drone ESC 14S battary 3 - T-Motor FLAME 100A 14S ESC 6-14S

Weight N/A
Parameter

100A 14S, 100A 6S

Customers reviews

There are no reviews yet.

Be the first to review “T-Motor FLAME 100A 14S ESC 6-14S”
Back to Top
Product has been added to your cart