CUAV NEO 3 GPS
$89.00
- Ublox M9N Module
- maximum accuracy 0.7 m
- Simultaneous receive four satellite systems
CUAV NEO 3 GNSS UAV Navigation Modules | GNSS U-blox M9N Drone Hardware
CUAV NEO 3 GPS uses a hardware design similar to NEO V2, and upgrades the GNSS navigation module to the M9N module that supports the four mainstream satellite systems of Beidou, GPS, Galileo and Glonass. The positioning accuracy has been significantly improved. It is a high Cost-effective unmanned system positioning and navigation module. It integrates compass, barometer, flight controller status light, buzzer, and safety switch in one; it has the characteristics of high sensitivity and strong anti-interference.
Follow us World Drone Market on our YouTube to view more about the CUVA NEO V3 GPS.
Features
- Buzzer prompt
- safety switch
- CAN Bus
- MS5611 Barometer
- RGB Status Light
- CROCOMM custom four-star high gain antenna
Ublox M9N Satellite receiver
New generation satellite receiver Ublox M9N，The actual measurement can reach a maximum accuracy of 0.7 m.
Simultaneous reception by the four satellite systems
U-BLOX M9N GPS Module Supports simultaneous reception of Beidou, Galileo, Glonas, and GPS four satellite systems
RM3100 industrial sensor
Using RM3100 industrial grade sensor, has better anti-interference performance
Triple filter design
CUAV NEO 3 Open Source GPS adopts SAW+LNA+SAW triple filter design, effectively avoiding the influence of remote control, data transmission, 4G signal on GPS positioning reception
- NEO V3 GNSS level accuracy when the SBAS enhancement system is turned on, the nominal accuracy is 1.5 m (default); when the SBAS enhancement system is turned off, it is 2.0 m
- NEO 3 supports RTCM3.3 injection, but does not support RTCM output; it can achieve pseudo range differential (meter-level positioning) but does not support carrier phase differential (RTK), and it needs a base station that supports RTCM3.3 output.
For installation and configuration, please visit CUAV NEO V3 GPS Manual
Check out the Pro version of CUAV GPS: CUAV NEO 3 Pro GPS
User Tutorial
Connect with V5+
Connect to [GPS&SAFETY] interface.
When you connect NEO 3 to autopilots of other brands (non-CUAV autopilots), the buzzer will not work. If you need to use it on autopilots of other brands, please select NEO 3 Pro.
Autopilot parameter settings
CUAV Neo 3 is a plug-and-play module without parameter settings.
| Weight | 0.25 kg |
|---|---|
| Dimensions | 10 × 10 × 5 cm |
1 review for CUAV NEO 3 GPS
01 Customer(s) recommended this item
-
Works perfectly, Gets lots of satellites quickly and magnetometer works really well
2021-10-07Verified Purchase
| Processor | STM32F412 |
| Compass | IST8310 |
| GNSS receiver | UBLOX NEO M9N |
| RGB drive | NC5623C |
| Buzzer | Passive buzzer |
| Safety switch | Physical button |
| GNSS | Beidou、Galileo、 GLONASS、 GPS |
| GNSS Augmentation System | SBAS:WAAS,EGNOS,MSAS QZSS:L1s(SAIF) other：RTCM3.3 |
| Number of concurrent GNSS | 4 |
| Frequency band | GPS:L1C/A GLONASS:L10F Beidou:B1I Galileo:E1B/C |
| Horizontal accuracy | 2.0M |
| Speed accuracy | 0.05M/S |
| Nav. update rate | 25Hz(Max) |
| Acquisition | Cold start：24S Hot start：2S Aided start:2s |
| Number of satellites(MAX) | 32+ |
| Sensitivity | Tracking and nav-167dBm Cold start Hot star-148dBm Reacquisition -160dBm |
| Protocol | UART+IO+I2C |
| Port TYpe | GHR-10V-S |
| Supported flight controller | CUAV series, Pixahwk series |
| Wave filtering | SAW+LNA+SAW |
| Anti-Electromagnetic/radio frequency interference | EMI+RFI |
| Upgrade firmware | support |
| Support Flight control type | Ardupilot/PX4*(PX4 is still working hard to adapt to the clock)Pixhawk |
| Input voltage | 5V |
| Operating temperature | -10~70℃ |
| Size | 60*60*16MM |
| Weight | 33g |
Related products
Sold out
Sold out
Sold out
Hot
Leave feedback about this
You must be logged in to post a review.